OEM Factory for Steel Coil Slitting Process - Metal Steel Coils Slitting Production Line – Raintech
OEM Factory for Steel Coil Slitting Process - Metal Steel Coils Slitting Production Line – Raintech Detail:
MAIN TECHNICAL PARAMETERS
Slitting line for thin material
| Model Parameter | Material Thicknes (mm) | Max.Coil Width(mm) | Slitting Strip Width (mm) | Slitting Speed(m/min.) | UncoilingWeight(Tons) |
| SSL-1*1300 | 0.15-1 | 500-1300 | 24 | 50-150 | 10 |
| SSL-2*1300 | 0.3-2 | 500-1300 | 12-30 | 50-200 | 15 |
| SSL-2*1600 | 0.3-2 | 500-1600 | 12-30 | 50-200 | 15 |
| SSL-3*1600 | 0.3-3 | 500-1600 | 8-30 | 50-180 | 20 |
| SSL-3*1850 | 0.3-3 | 900-1850 | 8-30 | 50-180 | 20 |
| SSL-4*1600 | 1-4 | 900-1600 | 6-30 | 50-150 | 25 |
| SSL-4*1850 | 1-4 | 900-1850 | 6-30 | 50-150 | 25 |
Mini slitting line
| SSSL-1*350 | 0.1-1 | 80-350 | 6-30 | 50-100 | 3 |
| SSSL-2*350 | 0.2-2 | 80-350 | 6-30 | 50-200 | 3 |
| SSSL-2*450 | 0.2-2 | 80-450 | 6-30 | 50-200 | 5 |
| SSSL-2*650 | 0.2-2 | 80-650 | 6-30 | 50-180 | 7 |
Slitting line for thick material
| Model Parameter | Material Thicknes(mm) | Max.Coil Width(mm) | Slitting Strip Number | Slitting Speed(m/min.) | UncoilingWeight(Tons) |
| SSL-6*1600 | 1-6 | 900-1600 | 6-30 | 30-100 | 25 |
| SSL-6*1850 | 1-6 | 900-1850 | 6-30 | 30-100 | 30 |
| SSL-6*2000 | 1-6 | 900-2000 | 6-30 | 30-100 | 30 |
| SSL-8*1600 | 1-8 | 900-1600 | 6-30 | 30-80 | 25 |
| SSL-8*1850 | 1-8 | 900-1850 | 6-30 | 30-80 | 25 |
| SSL-8*2000 | 1-8 | 900-2000 | 6-30 | 30-80 | 25 |
| SSL-12*1600 | 2-12 | 900-1600 | 5-30 | 20-50 | 30 |
| SSL-12*2000 | 2-12 | 900-2000 | 5-30 | 20-50 | 30 |
| SSL-16*2000 | 4-16 | 900-2000 | 5-30 | 10-30 | 30 |
PRODUCTION PROCESS
Loading trolley → Uncoiler → Guide device → Traction leveling machine → 1#Swing bridge → Rectifying feeding device → Slitting machine → Scrap edge winder → Passing frame → 2#Swing bridge → Pre → separating device → Tightening machine → Feeding device → Sub-coiling shear → Steering drum → Rear axle → Winder → Discharging trolley → Auxiliary support → Hydraulic system → Electrical system
MAIN COMPONENTS
| Loading/unloading trolley | There are two sets of trolleys, one for loading and one for unloading after slitting. |
| Double support decoiler | Tighten the coil material on the reel, unwind or recover the unfinished coil material. |
| Straight head feeder | The straight-head feeder is composed of a coil press roller, a bending roller, a shovel head, and a swing bridge. Each part is driven by an oil cylinder. |
| Leveling tractor | When in line operation, the leveling tractor drives the decoiler reel to open the material. |
| Swing bridge | There are two swing bridges, 1# pendulum bridge spans both sides of the pit;2#Swing bridge is located between the slitting machine and the tensioning machine. |
| Correction machine | The correcting machine is used to guide the feeding direction of the sheet material. It is mainly composed of a vertical guide roller, a sliding seat and an adjusting screw. |
| Slitting Machine | The slitting machine is composed of upper and lower knife shafts with cutter heads, fixed and movable supports, knife shaft spacing adjustment mechanism, transmission system, etc. |
| Scrap winder | On both sides of the discharge side of the slitting machine, there is a waste edge winder, which is used to collect the waste edge material from both sides of the sheet. The width of the waste material winding is 5-20mm. |
| Anticipating agency | At the turning point from the looper to the tensioner, a pre-separation mechanism is set up to prevent random materials |
| Leading machine | There is a pair of feeding rollers in front of the tensioner to facilitate feeding the material head into the winder |
| Tensioner | The tensioner exerts positive pressure on the slats to generate winding tension, which is convenient for tightening the slats. |
| Material head (tail) shearing machine (2 sets) | Used for cutting head and intermediate sub-roll |
| Approach bridge | Driven by the oil cylinder to lift and fall, it is used to introduce the material head into the winder drum after slitting. |
| Material dividing and pressing device | The device is located above the reel of the winder and consists of a distribution plate and a pressing wheel shaft |
| Winder | The winding machine is driven by a DC motor, and the speed is regulated by a DC speed regulator. |
| Auxiliary support | The auxiliary support is a toggle mechanism, which is lifted or lowered by the hydraulic cylinder to push the swing arm |
| Electrical System | The whole line adopts PLC for logic and real-time control of the whole line |
WORKPIECE SAMPLES
Product detail pictures:
Related Product Guide:
We generally believe that one's character decides products' top quality, the details decides products' high-quality ,along with the REALISTIC,EFFICIENT AND INNOVATIVE team spirit for OEM Factory for Steel Coil Slitting Process - Metal Steel Coils Slitting Production Line – Raintech , The product will supply to all over the world, such as: New Delhi, Juventus, Nicaragua, With more and more Chinese products and solutions around the world, our international business is developing rapidly and economic indicators big increase year by year. We have enough confidence to supply you both better solutions and service, because we've been more and more powerful, specialist and experience in domestic and international.
By Frank from Brazil - 2017.10.13 10:47
The manufacturer gave us a big discount under the premise of ensuring the quality of products, thank you very much, we will select this company again.
By David Eagleson from Morocco - 2018.02.12 14:52
Write your message here and send it to us
